Quantitative Valv-Chek 3.0 - Filler Valve Monitor

Identifies Erratic or Faulty Valves, Facilitates Filler Calibration and Set-Up, Eliminates Product “Give Away” and Signals Operator of Over/Under Filling

Rejects

Current Product

Average Fill Levels

Distribution Analysis

System Status Display

High and Low Filling Valves

Containers per Minute/Hour

Containers per Shift/Run

Alarms and more . . .

Standard Measure of Performance for High Speed Filling Lines

PECO’s Quantitative Valv-Chek is the “standard measure of performance” for high speed filling lines. The PECO Quantitative Valv-Chek is so economical that any size operation can afford the benefits of filler valve performance monitoring.

Easy Calibration and Multiple Product Memory Makes for Fast Changeovers

The easy to set-up and calibrate Quantitative Valv-Chek makes change over as easy as making a product selection on the pull down menu.

Printed Reports and Data Storage

Printed reports can be printed on demand or programmed to print at regular intervals. Data can be automatically saved at regular intervals, making SPC or tracking of performance over time extremely easy.

The User-Friendly Quantitative Valv-Chek System Displays a Wide Range of Statistical Data

System Status Display

The operational status of each system component is displayed on this report as well as current line conditions (rate and production).

Fill Level Distribution

The fill level distribution display presents the degree of dispersion for each valve. The "Sigma" or measure of standard deviation expresses this dispersion factor numerically.

Average Fill Level

The average fill level display shows the relative performance
up to 48 valves.

Display High/Low

The 17 highest and lowest filling valves are continuously displayed on a screen together with each corresponding standard deviation

Erratic Fills by Valve

Relative Valve Performance and Trending

Production vs. Budget

and more. . .

Quantitative Valv-Chek 3.0 Remote Display

Optional Remote Display

The Quantitative Valv-Chek monitoring unit is usually positioned at the transfer between filler and seamer or at the seamer/capper discharge with an optional remote display providing continuous data to the operator Including:

Current Product

Average Fill Volume

Containers Per Minute

Total Production Data

Alarm Conditions

Volumetric Measurement Principle

The inspection assembly of the Quantitative Valv-Chek 3.0 consists of a gamma radiation source and receiver. The volume of the container attenuates the radiation signal proportionately. The measured radiation change is translated into a volumetric measure (e.g. milliliters, ounces) based upon values established in
the calibration process.

Safety Considerations and Regulations

All PECO's gamma based systems are designed and manufactured to exceed the requirements of all state and federal safety regulations in countries where they are sold for use in food and beverage inspection applications.

**Technical Specifications**

**Inspection Assembly**
Power Requirements:	115 VAC or 230 VAC ±50/60 Hz, single phase, 130W
Operating Environment:	+5°C to 60°C (40°F to 140°F) 0% to 95% relative humidity
Dimensions:	635mm (25 in.) wide x 305mm (12 in.) high x152mm (6 in.) deep
Material:	Stainless Steel Enclosure with acetyl co-polymer display cover
Operating Parameters:	Speed - up to 2,400cpm Filler Size - up to 200 valves Dynamic Range - dependent on container size and shape. 30ml typical on 350ml ca

**Remote Display Monitor**
Power Requirements:	115 VAC or 230 VAC
Operating Environment:	+5°C to 60°C (40°F to 140°F) 0% to 95% relative humidity
Dimensions:	457mm (18 in.) wide x 254mm (10 in.) high x127mm (5 in.) deep
Material:	Stainless Steel Enclosure with acetyl co-polymer display cover
Display:	Vacuum fluorescent display Four rows of display with 20 characters per row

Next >

Peco Controls